How To Install Fish Finder

How To Install Fish Finder?

How To Install Fish Finder? – Fish finders are a great tool for expeditions. It can be cumbersome if it isn’t installed correctly. You should make sure the fish finder is in a place that is easy to read, and easy to access. When installing a Fishfinder, there are some things that you might not have thought of.

These include the placement of the wires and how they will run. Although it might seem easy to install a Fishfinder, there are many mistakes that people make. This tutorial will help you install a Fishfinder and make it a useful tool.

Guide to Install Fish Finder

You need the right tools to install your fishfinder. If you don’t have all the tools you need, it can make starting a project difficult. It’s a good idea to run through this checklist to make sure you have all the tools. Most hardware stores will lend you tools if you need them. Although most tools can be found at home, some may require you to go out and purchase them. Before you begin installing your fish finder, here are some things you should know.

  • Phillips head screwdriver
  • Wire fish
  • Wire stripper
  • Wire crimper
  • Fishing rods
  • Adhesive 3M 5200
  • Heat shrink tubing with adhesive-lined heat
  • Cable ties
  • Mounting hardware
  • Silicon sealant
  • Clamshell fitting
  • Connectors for terminals
  • If applicable, crimped barrel connectors

How to Install a Fishfinder: Step by Step Instructions?

Step 1: Register the Fishfinder

Before you can start working on your boat, you want to make sure your fish finder is registered. Your email address will be entered into the system by the manufacturer of your fish finder. This allows them to reach you. If you have any issues with your fish finder, you can contact the manufacturer, and they can guide you through the process to get your fish finder back on track. You will receive updates and alerts so that your fish finder is always ready for use. You’ll always have the latest information for your fishfinder. It will always be available to you, wherever you are.

Step 2: Update Fish Finder Software

When you remove the box from the fish finder, it will ask you to update its software. When you remove the box, it is important to update the software immediately. There are some fish finders that include micro SD slots, which allow you to increase the memory, and store more pictures. Before you can use the SD card, you may need to format it. You can use the fish finder immediately by following the steps to update it instead of waiting. These two steps should be completed before you install the fish finder. If you don’t, the mount will need to be attached. This can prove annoying when updating the software.

Step 3: Locate the Right Spot

When you’re looking at your boat, you want to consider where you’re going to put the mount. The mount should be placed near the boat’s helm and easily visible. It is important to ensure that the fish finder is at the right angle for your body. Typically, a fishfinder should be between your waistline and your shoulder height. The fish finder should be placed in a spot that is easy to reach. This will allow you to concentrate on driving and the fish finder at the same time.

Step 4: Find the Power Source

You need to ensure that the wires reach the power source, depending on the type of power source. It is possible to attach the wires directly to a battery. This is the safest and most efficient way to connect your wires. The wires should reach the desired destination easily without allowing too much space. After drilling the holes, you can shorten or lengthen wires. It will be much easier to put the fish finder in place once you have identified the location of the power source and the place where it is located.

Step 5: Drill your spot for the Mount and Wires

Once you have a plan for where the fish finder will be placed, drill the holes for mounting the wires and mounting the mount. You want to power the drill at full speed, so it doesn’t catch on any of the edges and cause splinters. You should mark the entry and exit points for the wires of your unit. Check to see if there was a hole in the unit where a fish finder once resided. You will need to drill another hole behind the binnacle mount if you want to drill a new location. Make sure the hole is large enough for wires to pass through. To test if the wires work, you can place the fish finder and binnacle in the holes.

Step 6: Apply sealant

Before mounting the fish finder and winding the wires, sealant should be applied around the holes. Although you don’t have to use too much sealant it will keep everything in its place. Once you have filled the holes with sealant, apply it to the bolts holding the fish finder mount. This sealant creates a stronger bond and protects your fish finder mount from being damaged. Your fish finder shouldn’t fall off its mount when you are out in open water.

Step 7: Follow the Power Leads

You should check the length of the wires before you run them through the holes. You will need to ensure that the wires are of the same color and the recommended gauges. If you have to extend the wires, you should use crimped barrel connectors. You don’t have to worry about the in-line fuse from the manufacturer getting in your way. After drilling the exit hole, the wires will run to the power supply. You can leave the wires attached to the fish finder for now. Make sure that the wires are securely wrapped with ties.

Step 8: Connect the wires to the transducer

The transducer displays the information on the fish finder’s display. You should place the transducer in the boat’s deepest section. Anything that could cause water to rise should be avoided. The transducer mount should be held against the transom. Next, run the wires to and from the dash. Mark the location of the mount and then install the wire. Do not cut the wire and do not mix the transducer wire and the engine wiring harness.

Step 9: Install your Transducer

Once you have connected the wire to the transducer boat, it is time to install it. Connect the transducer to the wires and mark the mount for the transducer. Apply sealant generously. To prevent water from getting into your boat through the holes that you have drilled, make sure to apply a thick seal. Your transducer should now be in good working order.

Step 10: Connect the System

The top of your boat is where you will place your fish finder. Before you attach the wires to your fish finder, make sure that the battery is off. The silicon sealant can be used to seal the wire hole behind the binnacle mounting. Once you have connected all the wires to the fish finder, make sure that you are getting power.

If your fish finder won’t turn on, check that the wires are properly connected. You can adjust the settings to see the transducer if it turns on. Before you take your boat out on the water, make sure that the sealant has dried completely. Your fish finder won’t cause your boat sink. To ensure that the sealant is intact, you can check it every week. You’ll be fine if there are no leaks within a week.

How To Install A Fishfinder On A Fiberglass Boat?

What is the difference between hoping for the best, and making sure you have the best chance of catching a fish? Simple: a fishfinder. Too many fiberglass boat owners worry that installing a fishfinder to their boat will prove too difficult. There’s good news! You can do it yourself. These are the best ways to install a fishfinder on a fiberglass boat.

The Foundation for Your Fishfinder

Setting the foundation is one of the biggest problems for fiberglass boat owners. Most fiberglass boats require a binnacle mount to be installed. These are the key steps:

  • Localization Which is the best spot for your fishfinder to be placed? You should bring a tape measure so you can determine how much space you have. It’s important to pick a location that is easy to see from the cockpit. To ensure that the space is adequate for the installation, you will also need to inspect the underside and back of the location. Make sure to find the power bus, and ensure you have the terminals for any additional electronics.
  • Drill the mounting holes. Measure twice, cut once – or in this instance, drill once. Although it might seem tempting to drill slowly, drilling can be smoother if the drill is operated at full speed.
  • The wiring. It is important to make sure that the wires can reach the fishfinder. First, look for holes that have been drilled previously. If you don’t find any, you might need to drill another hole behind the mount.

Once you have the holes in place, you can use silicone sealant to seal the holes. Attach the binnacle and seal each bolt with a bit of sealant.

Give your fishfinder power

You can now feed the power cables through the hole you have already made through the back. You should leave enough room for the power leads to pass through, but not too much. Secure the wires with tie-wraps and clamps every one and half feet.

Depending on the way your unit works, there may be additional work. If your fuse block has male terminals, for example, you might need to use female connectors. The wires may need to be lengthened or shortened. Make sure you do not cut the in-line fuse supplied by the manufacturer. This could cause your unit to be damaged and invalidate the warranty.

Finalizing the Installation

These steps will help you mount your transducer. After you have found the perfect spot for your bracket, hold it against the transom. You can move it around to ensure that it is in the right place. To ensure it stays horizontal, you may need to balance it. You will need to mark the exact location where the bracket’s mounting holes end.

Next, connect the transducer’s wiring to the dash. Once the wiring is pulled through, coil any additional wire inside. Make sure to use clamps to secure the wire. This will prevent your fishfinder from performing as well as possible. The transducer wire should be kept separate from the engine’s wiring harness and the VHF cable.

Make sure to drill the holes where the markings were made earlier. Use an adhesive/sealant to coat the clean screws as well as the clean insides of the transom holes. Now you can screw the mount in. This is where you want to make sure that the mount seals well.

Placement of the Fishfinder

Use a clamshell vent to seal the hole in the wiring that you have drilled previously, the one behind the binnacle mounting. This will keep it watertight and still easily accessible. Once you have completed the previous steps, you can place the fishfinder in its proper spot and complete the wiring.

If you find any steps too difficult, consult the owner’s or manufacturer’s manuals. Although it may take some time to understand everything, once your fishfinder is installed and functioning properly, it will be worth it.

Caring for your Fiberglass Boat

We recommend that you use BoatLIFE sealants to keep your boat watertight. While you are working on your boat, use Fiberglass Rubbing Compound or Life Wax to protect it.

Final Thoughts

Is everything working flawlessly? Excellent job. You’ve done a great job. Now, trade those tools for some bait and a rod. Find out how the new fishfinder can help you fill your cooler. To protect your new unit, make sure you get a waterproof cover. The majority of covers offered by manufacturers protect only the LCD screen. However, a cover that covers the entire fishfinder is better.

Lewis
Lewis Mark is a vastly experienced fly fisher. His encyclopedic knowledge of fly tying has led to start blog on fishing. He also review Fishing equipment based on his knowledge and experience.